Saving state before power failure This parameter allows to choose operating for the 1st channel controlled by the S1 switch. This parameter determines how the device in timed mode reacts to pushing the switch connected to the S1 terminal. This parameter allows to set time parameter used in timed modes. (s) This parameter allows to set time of switching to opposite state in flashing mode. 1-32000 (0.1-3200.0s, 0.1s step) This parameter allows to choose operating for the 2nd channel controlled by the S2 switch. This parameter determines how the device in timed mode reacts to pushing the switch connected to the S2 terminal. This parameter allows to set time parameter used in timed modes. (s) This parameter allows to set time of switching to opposite state in flashing mode. 1-32000 (0.1-3200.0s, 0.1s step) Inputs type configuration Enabled / Disabled reports on Flashing mode This parameter defines how commands are sent to specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st lifeline group. 1 - 2nd group sent as secure. 2 - 3rd group sent as secure. 4 - 4th group sent as secure. 8 - 5th group sent as secure. Default setting: 15 (all) This parameter determines which actions result in sending scene IDs assigned to them. 1 - Key pressed 1 time. 2 - Key pressed 2 times. 4 - Key pressed 3 times. 8 - Key Hold Down and Key Released. Default setting: 0 (none) This parameter determines which actions result in sending scene IDs assigned to them. 1 - Key pressed 1 time. 2 - Key pressed 2 times. 4 - Key pressed 3 times. 8 - Key Hold Down and Key Released. Default setting: 0 (none) This parameter determines which actions are ignored when sending commands to devices associated in 2nd and 3rd association group. All actions are active by default. 1 - ignore turning On with 1 click of the switch. 2 - ignore turning OFF with 1 click of the switch. 4 - ignore holding and releasing the switch. 8 - ignore double click of the switch. Default setting: 0 This parameter determines value sent with Switch On command to devices associated in 2nd and 3rd association group. This parameter determines value sent with Switch Off command to devices associated in 2nd and 3rd association group. This parameter determines value sent with Double Click command to devices associated in 2nd and 3rd association group. This parameter determines which actions are ignored when sending commands to devices associated in 4th and 5th association group. All actions are active by default. 1 - ignore turning On with 1 click of the switch. 2 - ignore turning OFF with 1 click of the switch. 4 - ignore holding and releasing the switch. 8 - ignore double click of the switch. Default setting: 0 This parameter determines value sent with Switch On command to devices associated in 4th and 5th association group. This parameter determines value sent with Switch Off command to devices associated in 4th and 5th association group. This parameter determines value sent with Double Click command to devices associated in 4th and 5th association group. This parameter determines how the device will react to General Alarm frame. This parameter determines how the device will react to Flood Alarm frame. This parameter determines how the device will react to CO/CO2/Smoke Alarm frame. This parameter determines how the device will react to Heat alarm frame. This parameter allows to set duration of flashing alarm mode. 1-32000 (0.1-32000s, 1s step) Default: 600 (10min) This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. 1-100 (%) Default 20 (20%) This parameter determines minimum time that has to elapse before sending new power report to the main controller. 1-120 (s) Default 10 (10s) This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. 1-32000 (0.01-320 kWh) Default 100 (1kWh) This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. 1-100 (%) Default 20 (20%) This parameter determines minimum time that has to elapse before sending new power report to the main controller. 1-120 (s) Default 10 (10s) This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller 1-32000 (0.01-320 kWh) Default 100 (1kWh) This parameter determines in what time interval the periodic power reports are sent to the main controller. 1-32000 (s) Default 3600 (1h) This parameter determines in what time interval the periodic power reports are sent to the main controller. 1-32000 (s) Default 3600 (1h) This parameter determines whether energy metering should include the amount of energy consumed by the device itself. Results are being added to energy reports for first endpoint.