Retour d'état mais pas d'action

Hello
je continue ma remise à plat de me pluggins
j’ai installé un peu de enocean, l’histoire de tester et aussi de piloter des wc dans lesquels je n’avais pas de knx
Bref je suis sur un jeedom 4 et le dongle enocean avec une belle antenne
je viens de refaire les inclusions de mes modules 2x 2 interrupteurs et un module volet roulant
L’inclusion s’est faite sans problèmes
j’ai aussi les retours d’état et de positionnement du volet par exemple
là où le bas blesse, c’est que lorsque je teste une action, ON, OFF ou montée/descendre rien ne se passe
j’ai mis en mode debug, mais je ne vois rien d’évidemment faux

est ce que quelqu’un a déjà eu le problème ?, là je sèche

[2020-12-05 14:03:06][DEBUG] : Client connected to [127.0.0.1:43010]
[2020-12-05 14:03:06][DEBUG] : Message read from socket: {"apikey":"monapikeyamoiquejaichangecarjesuisunmalin","cmd":"send","dest":"051A4AC8","profile":{"func":"05","rorg":"d2","type":"00"},"command":{"CMD":"1","POS":"0"}}
[2020-12-05 14:03:06][DEBUG] : Client disconnected from [127.0.0.1:43010]
[2020-12-05 14:03:06][DEBUG] : Message received in socket JEEDOM_SOCKET_MESSAGE
[2020-12-05 14:03:06][DEBUG] : Received command from jeedom : send
[2020-12-05 14:03:06][DEBUG] : Send command
[2020-12-05 14:03:06][DEBUG] : {u'CMD': 1, u'POS': 0} on command None 210 5 0
[2020-12-05 14:03:06][DEBUG] : [85, 0, 10, 7, 1, 235, 210, 0, 0, 0, 1, 255, 184, 218, 128, 0, 3, 5, 26, 74, 200, 255, 0, 5]
[2020-12-05 14:03:06][DEBUG] : Last packet for this 05:1A:4A:C8 was emited 793.184817791 seconds ago
[2020-12-05 14:03:06][INFO] : Sending packet
[2020-12-05 14:03:06][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x0', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 0%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 0}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:06][INFO] : Sending packet
[2020-12-05 14:03:06][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x0', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 0%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 0}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:06][INFO] : Sending packet
[2020-12-05 14:03:06][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x0', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 0%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 0}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:06][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:06][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:06][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:06][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:06][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:06][DEBUG] : Response is : OK
[2020-12-05 14:03:06][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:06][DEBUG] : Response is : OK
[2020-12-05 14:03:06][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:06][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:06][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:06][DEBUG] : Response is : OK
[2020-12-05 14:03:12][DEBUG] : Client connected to [127.0.0.1:43054]
[2020-12-05 14:03:12][DEBUG] : Message read from socket: {"apikey":"monapikeyamoiquejaichangecarjesuisunmalin","cmd":"send","dest":"051A4AC8","profile":{"func":"05","rorg":"d2","type":"00"},"command":{"CMD":"1","POS":"100"}}
[2020-12-05 14:03:12][DEBUG] : Client disconnected from [127.0.0.1:43054]
[2020-12-05 14:03:12][DEBUG] : Message received in socket JEEDOM_SOCKET_MESSAGE
[2020-12-05 14:03:12][DEBUG] : Received command from jeedom : send
[2020-12-05 14:03:12][DEBUG] : Send command
[2020-12-05 14:03:12][DEBUG] : {u'CMD': 1, u'POS': 100} on command None 210 5 0
[2020-12-05 14:03:12][DEBUG] : [85, 0, 10, 7, 1, 235, 210, 100, 0, 0, 1, 255, 184, 218, 128, 0, 3, 5, 26, 74, 200, 255, 0, 205]
[2020-12-05 14:03:12][DEBUG] : Last packet for this 05:1A:4A:C8 was emited 6.53965497017 seconds ago
[2020-12-05 14:03:12][INFO] : Sending packet
[2020-12-05 14:03:12][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x64', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 100%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 100}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:12][INFO] : Sending packet
[2020-12-05 14:03:12][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x64', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 100%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 100}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:12][INFO] : Sending packet
[2020-12-05 14:03:12][DEBUG] : FF:B8:DA:80->05:1A:4A:C8 (-255 dBm): 0x01 ['0xd2', '0x64', '0x0', '0x0', '0x1', '0xff', '0xb8', '0xda', '0x80', '0x0'] ['0x3', '0x5', '0x1a', '0x4a', '0xc8', '0xff', '0x0'] OrderedDict([(u'POS', {u'value': u'Output position 100%', u'description': u'Vertical position', u'unit': u'', u'raw_value': 100}), (u'ANG', {u'value': u'Output angle 0%', u'description': u'Rotation angle', u'unit': u'', u'raw_value': 0}), (u'REPO', {u'value': u'Go directly to POS/ANG', u'description': u'Repositioning', u'unit': u'', u'raw_value': 0}), (u'LOCK', {u'value': u'Do not change', u'description': u'Locking modes', u'unit': u'', u'raw_value': 0}), (u'CHN', {u'value': u'Channel 1', u'description': u'Channel', u'unit': u'', u'raw_value': 0}), (u'CMD', {u'value': u'Goto Command', u'description': u'Command Id', u'unit': u'', u'raw_value': 1})])
[2020-12-05 14:03:12][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:12][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:12][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:12][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:12][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:12][DEBUG] : Response is : OK
[2020-12-05 14:03:12][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:12][DEBUG] : Response is : OK
[2020-12-05 14:03:12][DEBUG] : [85, 0, 1, 0, 2, 101, 0, 0]
[2020-12-05 14:03:12][DEBUG] : 0x02 ['0x0'] [] OrderedDict()
[2020-12-05 14:03:12][DEBUG] : Receive response packet : 2
[2020-12-05 14:03:12][DEBUG] : Response is : OK

Bon petit update

Sur l’ancien Forum , @Patrick avait bien détaillé le principe
Du coup, j’ai retenté ma chance
D’abord j’ai refait les inclusions , j’ai 2 modules doubles et un module volet )
1- je suis passé en mode exclusion
2- j’ai supprimer le module depuis jeedom
3-je suis repassé en mode inclusion
4- j’ai mis mes modules en mode learn

Les 3 s’apparient nikel avec Jeedom
Le premier qui éclaire mes toilettes ( étage et rdc) s’affiche, par acquis de conscience je teste les statuts puis les actions et là bonheur, ça fonctionne

Ni une ni deux je passe au module suivant qui est juste à côté de lui dans mon tableau électrique, il remonte bien dans Jeedom mais les actions ne fonctionnent pas

Pareil pour mon volet
J’ai tenté de repasser en mode learn et cliquer sur monter pour le volet et on pour l’autre mais rien n’y fait
grrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr

J’ai du loupé un truc.
Le plus rageant c’est que j’ai supprimé le module WC sans faire exprès, je l’ai ajouté de nouveau et ça fonctionne toujours

Je sais que ceux sont de vieux sujets et quand ça fonctionne on n’y touche plus mais là je sèche :unamused:

Je fais une réponse à moi même qui n’en est pas une, c’est juste pour que ma question ne tombe pas dans l’oubli et qu’avec un peu de chance quelqu’un la lira :sleepy: :grin:

Peux-tu préciser la marque et le modèle du module volet roulant qui pose problème ?

c’est le Micromodule nodon volets roulants et le module éclairage double

Hello

Je confirme que j’ai enfin réussit à faire reconnaitre Jeedom par mes modules Nodon
Aide bug Enocean et à @Touf2638

j’ai donc suivi ce protocole
D’abord j’ai refait les inclusions , j’ai 2 modules doubles et un module volet )
1- je suis passé en mode exclusion
2- j’ai supprimer le module depuis jeedom
3- j’ai redémarré le daemon
4-je suis repassé en mode inclusion
5- j’ai mis mes modules en mode learn ( appuie 3 fois sur le bouton)
6-j’ai testé les remontées d’information et c’était OK
7- j’ai redémarré le daemon
8- j’ai mis mes modules en mode learn ( appuie 3 fois sur le bouton)
9-j’ai cliqué sur ON ou sur descendre pour les volets, mes commandes sont inversées
et miracle ça fonctionne